AccScience Publishing / IJB / Online First / DOI: 10.36922/IJB026330352
Cite this article
1
Download
43
Views
Related Info Links
More by Authors Links
Journal Browser
Volume | Year
Issue
Search
News and Announcements
View All
RESEARCH ARTICLE

Development and validation of a low-cost, open-source robotic extrusion printing platform for acellular hydrogel scaffold fabrication: A step toward multi-axis robotic bioprinting

Kenneth Houston1 ,  Perrin Woods1 ,  Ahasan Habib1*
Show Less
1 Department of Mechanical and Mechatronics Engineering Technology, College of Engineering Technology, Rochester Institute of Technology, Rochester, New York , United States of America
Received: 10 August 2026 | Revised: 15 October 2026 | Accepted: 15 October 2026 | Published online: 18 November 2026
(This article belongs to the Special Issue Innovations in Bioprinting Technologies for Tissue Engineering)
© 2026 by the Author(s). This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution 4.0 International License ( https://creativecommons.org/licenses/by/4.0/ )
Abstract

Commercial multi-axis robotic bioprinting platforms remain prohibitively expensive for many laboratories, limiting access to robot-assisted biofabrication. This study converted a low-cost six-axis industrial robot (ABB IRB 120T with IRC5 Compact controller) into an open-source robotic extrusion printing platform and compared its dimensional performance with a commercial robotic bioprinter (BioAssemblyBot 400). Validation was limited to acellular hydrogel and planar toolpaths; cell-laden and non-planar printing remain necessary for biological validation. The platform integrated a modified printhead, elevated glass print bed, solenoid-based extrusion control, and a software pipeline that translated slicer-generated G-code into ABB RAPID motion and I/O commands. Five scaffolds were printed using the developed platform and three using the commercial system with a 4% alginate–4% carboxymethylcellulose bioink. The retrofitted platform demonstrated higher repeatability, with a mean coefficient of variation of 2.25% and maximum dimensional range of 0.388 mm, compared with 5.07% and 1.130 mm for the commercial system. Scaffold-level analysis (n = 5 vs. n = 3) showed significantly lower macro-scale dimensional variance for the retrofitted system, while pore-scale variance was lower but not statistically significant. No statistically significant difference between platforms was detected for overall-dimension or Y-direction pore-width accuracy, whereas the retrofitted system showed better X-direction pore-length accuracy in the pooled analysis. The total development cost was $16,617, an 89.6% reduction relative to the commercial system. These findings demonstrate a technically viable, substantially lower-cost pathway to multi-axis robotic biofabrication, with remaining dimensional limitations likely tied to bioink processing and the absence of crosslinking rather than robotic motion control.

Keywords
Extrusion bioprinting
Robotic bioprinting
Six-axis industrial robot
G-code-to-RAPID translation
Open-source bioprinter
Dimensional accuracy validation
Funding
The authors received no financial support for the research, authorship, and/or publication of this article.
Conflict of interest
The authors declare they have no competing interests.
References
  1. Mandrycky C, Wang Z, Kim K, Kim DH. 3D bioprinting for engineering complex tissues. Biotechnol Adv. 2016;34(4):422-434. doi: 10.1016/j.biotechadv.2015.12.011
  2. Naghieh S, Chen X. Printability—a key issue in extrusion-based bioprinting. J Pharm Anal. 2021;11(5):564-579. doi: 10.1016/j.jpha.2021.02.001
  3. Amorim PA, d'Ávila MA, Anand R, Moldenaers P, Van Puyvelde P, Bloemen V. Insights on shear rheology of inks for extrusion-based 3D bioprinting. Bioprinting. 2021;22:e00129. doi: 10.1016/j.bprint.2021.e00129
  4. Rohauer R, Schimmelpfennig K, Mei V, Woods P, Lewis CL, Habib MA. Characterization and prediction of properties of polymeric materials for extrusion-based bioprinting process. In: Proceedings of ASME 2025 20th International Manufacturing Science and Engineering Conference (MSEC2025). Vol 1. New York, NY: American Society of Mechanical Engineers; 2025. doi: 10.1115/MSEC2025-155176
  5. Strauß S, Schroth B, Hubbuch J. Evaluation of the reproducibility and robustness of extrusion-based bioprinting processes applying a flow sensor. Front Bioeng Biotechnol. 2022;10:831350. doi: 10.3389/fbioe.2022.831350
  6. Kirchmajer DM, Gorkin R 3rd. An overview of the suitability of hydrogel-forming polymers for extrusion-based 3D-printing. J Mater Chem B. 2015;3(20):4105-4117. doi: 10.1039/C5TB00393H
  7. Boularaoui S, Al Hussein G, Khan KA, Christoforou N, Stefanini C. An overview of extrusion-based bioprinting with a focus on induced shear stress and its effect on cell viability. Bioprinting. 2020;20:e00093. doi: 10.1016/j.bprint.2020.e00093
  8. Kačarević ŽP, Rider PM, Alkildani S, et al. An introduction to 3D bioprinting: possibilities, challenges and future aspects. Materials (Basel). 2018;11(11):2199. doi: 10.3390/ma11112199
  9. Kahl M, Gertig M, Hoyer P, Friedrich O, Gilbert DF. Ultra-low-cost 3D bioprinting: modification and application of an off-the-shelf desktop 3D-printer for biofabrication. Front Bioeng Biotechnol. 2019;7:184. doi: 10.3389/fbioe.2019.00184
  10. Tong A, Pham QL, Abatemarco P, et al. Review of low-cost 3D bioprinters: state of the market and observed future trends. SLAS Technol. 2021;26(4):333-366. doi: 10.1177/24726303211020297
  11. Thai MT, Phan PT, Tran HA, et al. Advanced soft robotic system for in situ 3D bioprinting and endoscopic surgery. Adv Sci (Weinh). 2023;10(12):2205656. doi: 10.1002/advs.202205656
  12. Urhal P, Weightman A, Diver C, Bartolo P. Robot assisted additive manufacturing: a review. Robot Comput Integr Manuf. 2019;59:335-345. doi: 10.1016/j.rcim.2019.05.005
  13. Vasques CMA, Figueiredo FAV. The 3D-printed low-cost delta robot Oscar: technology overview and benchmarking. Eng Proc. 2021;11(1):43. doi: 10.3390/ASEC2021-11173
  14. Shojaei Barjuei E, Shin J, Kim K, Lee J. High-precision multi-axis robotic printing: optimized workflow for complex tissue creation. Bioengineering (Basel). 2025;12(9):949. doi: 10.3390/bioengineering12090949
  15. Yang S, Kim H, Rezayof O, et al. Development and quantitative evaluation of a novel autonomous in situ bioprinting surgical robotic framework for treatment of volumetric muscle loss injuries. IEEE Trans Autom Sci Eng. 2025;22:2565-2576. doi: 10.1109/TASE.2024.3382200
  16. Albrecht FB, Schmidt FF, Schmidt C, Börret R, Kluger PJ. Robot-based 6D bioprinting for soft tissue biomedical applications. Eng Life Sci. 2024;24(7):e2300226. doi: 10.1002/elsc.202300226
  17. Fortunato GM, Batoni E, Pasqua I, Nicoletta M, Vozzi G, De Maria C. Automatic photo-cross-linking system for robotic-based in situ bioprinting. ACS Biomater Sci Eng. 2023;9(12):6926-6934. doi: 10.1021/acsbiomaterials.3c00898
  18. Fortunato GM, Sigismondi S, Nicoletta M, et al. Analysis of the robotic-based in situ bioprinting workflow for the regeneration of damaged tissues through a case study. Bioengineering (Basel). 2023;10(5):560. doi: 10.3390/bioengineering10050560
  19. Shojaei Barjuei E, Shin J, Kim K, Lee J. Precision improvement of robotic bioprinting via vision-based tool path compensation. Sci Rep. 2024;14(1):17764. doi: 10.1038/s41598-024-68597-z
  20. Ribeiro FM, Pires JN, Azar AS. Implementation of a robot control architecture for additive manufacturing applications. Ind Robot. 2019;46(1):73-82. doi: 10.1108/IR-11-2018-0226
  21. ABB. Application Manual: 3D Printing. Document ID 3HAC073941-001. Zurich, Switzerland: ABB; 2024. Accessed November 13, 2026. https://library.abb.com/d/3HAC073941-001
  22. Nilsson D. G-code to RAPID translator for RobotStudio. 2016.
  23. Pan J, Fu Z, Xiong J, Lei X, Zhang K, Chen X. RobMach: G-code-based off-line programming for robotic machining trajectory generation. Int J Adv Manuf Technol. 2022;118(7):2497-2511. doi: 10.1007/s00170-021-08082-3
  24. Woods P, Smith C, Clark S, Habib A. Integrating pneumatic and thermal control in 3D bioprinting for improved bio-ink handling. Designs. 2024;8(4):83. doi: 10.3390/designs8040083
  25. Woods P, Houston K, Sakib N, Lewis CL, Habib A. From gantry systems to robotic arms: a versatile hybrid 3D bioprinting nozzle with real-time UV curing. In: Proceedings of ASME 2025 20th International Manufacturing Science and Engineering Conference (MSEC2025). Vol 1. New York, NY: American Society of Mechanical Engineers; 2025. doi: 10.1115/MSEC2025-155441
  26. UltiMaker. Cura Software. Version 5.5.0. Geldermalsen, Netherlands: UltiMaker. Accessed November 13, 2026. https://ultimaker.com/software/ultimaker-cura/
  27. Khoda B, Habib MA. 3D bioprinting with cellulose-derived bio-ink and precursors. In: Klemmt C, Beaucage G, eds. Biodegradable 3D-Printing. Singapore: Springer; 2026:71-98. doi: 10.1007/978-981-95-4025-9_5
  28. Habib A, Sathish V, Mallik S, Khoda B. 3D printability of alginate-carboxymethyl cellulose hydrogel. Materials (Basel). 2018;11(3):454. doi: 10.3390/ma11030454
Share
Back to top
International Journal of Bioprinting, Electronic ISSN: 2424-8002 Print ISSN: 2424-7723, Published by AccScience Publishing