A review on defect suppression of melt growth ceramics prepared by laser-directed additive manufacturing
Melt growth ceramics (MGCs) exhibit exceptional high-temperature strength and microstructural stability near their melting points, positioning them as promising candidates for next-generation high-temperature structural materials intended for long-term service in extreme high-temperature oxidizing environments. Laser-directed additive manufacturing (LDAM), as an efficient, flexible, and environmentally friendly near-net-shaping technology, offers a novel approach to overcome the limitations of traditional MGC fabrication methods in terms of efficiency, quality, and achievable structural complexity. However, the rapid melting and solidification inherent in LDAM make MGCs highly prone to defect formation, which severely hinders the advancement of LDAM of MGCs (MGCs-LDAM). Therefore, this paper systematically reviews the formation mechanisms of two common defects—pores and cracks—in MGCs-LDAM, and summarizes the research progress on defect suppression. Finally, future research directions and key scientific challenges in this field are discussed. It is emphasized that quantitative defect characterization and in-depth analysis of formation mechanisms represent the primary current challenges. The development of innovative processing technologies is the key to overcoming the existing bottlenecks and promoting the development and application of MGCs-LDAM.
- Fu HZ. Directional Solidification Processing of Aero-High Temperature Materials. Beijing, China: Science Press; 2015:5-15.
- Padture NP. Advanced structural ceramics in aerospace propulsion. Nat Mater. 2016;15(8):804-809. doi: 10.1038/nmat4687
- Pollock TM. Alloy design for aircraft engines. Nat Mater. 2016;15(8):809-815. doi: 10.1038/nmat4709
- Zhang J, Lou L, Li H. Material and processing technology of directionally solidified blade in heavy duty industrial gas turbines. Mater China. 2013;32(1):12-23. [In Chinese]. doi: 10.7502/j.issn.1674-3962.2013.01.02
- Acevedo R, Sedlak P, Kolman R, Fredel M. Residual stress analysis of additive manufacturing of metallic parts using ultrasonic waves: state of the art review. J Mater Res Technol. 2020;9(4):9457-9477. doi: 10.1016/j.jmrt.2020.05.092
- Pastor JY, Martín A, Molina-Aldareguía JM, et al. Superplastic deformation of directionally solidified nanofibrillar Al2O3-Y3Al5O12-ZrO2 eutectics. J Eur Ceram Soc. 2013;33(13-14):2579-2586. doi: 10.1016/j.jeurceramsoc.2013.03.033
- Williams JC, Starke EA Jr. Progress in structural materials for aerospace systems. Acta Mater. 2003;51(19):5775-5799. doi: 10.1016/j.actamat.2003.08.023
- Ochiai S, Ueda T, Sato K, et al. Deformation and fracture behavior of an Al2O3/YAG composite from room temperature to 2023 K. Compos Sci Technol. 2001;61(14):2117-2128. doi: 10.1016/S0266-3538(01)00159-2
- Tang JM. A review of aerospace materials. Spacecr Environ Eng. 2013;30(2):115-121. [In Chinese]. doi: 10.3969/j.issn.1673-1379.2013.02.001
- Ni M, Zhu H, Qiu Y, Xu D, Liu S. Review on cooling technologies for turbine blades of aeroengine. Gas Turbine Technol. 2005;18(4):25-38. [In Chinese]. doi: 10.3969/j.issn.1009-2889.2005.04.006
- Liu DX. One generation of new material, one generation of new type engine: development trend of aero-engine and its requirements for materials. J Mater Eng. 2017;45(10):1-5. [In Chinese]. doi: 10.11868/j.issn.1001-4381.2017.100001
- Du K, Chen Q, Meng X, et al. Application and thermal analysis research progress of ceramic matrix composites in aero-engine hot-section components. J Propuls Technol. 2022;43(2):107-125. [In Chinese]. doi: 10.13675/j.cnki.tjjs.210380
- Binner J, Porter M, Baker B, et al. Selection, processing, properties and applications of ultra-high temperature ceramic matrix composites, UHTCMCs—a review. Int Mater Rev. 2020;65(7):389-444. doi: 10.1080/09506608.2019.1652006
- Xiang Y, Wang Y, Zhu C, et al. Research progress on oxide/oxide ceramic matrix composites. Adv Ceram. 2020;41(6):394-404. [In Chinese]. doi: 10.16253/j.cnki.37-1226/tq.2020.06.003
- Ngo TD, Kashani A, Imbalzano G, Nguyen KTQ, Hui D. Additive manufacturing (3D printing): a review of materials, methods, applications and challenges. Compos B Eng. 2018;143:172-196. doi: 10.1016/j.compositesb.2018.02.012
- Su H, Wang E, Ren Q, Zhang J, Liu L, Fu H. Research progress in ultra-high temperature oxide eutectic composite ceramics. Mater China. 2018;37(6):437-447. [In Chinese]. doi: 10.7502/j.issn.1674-3962.2018.06.05
- Nakagawa N, Ohtsubo H, Mitani A, Shimizu K, Waku Y. High temperature strength and thermal stability for melt growth composite. J Eur Ceram Soc. 2005;25(8):1251-1257. doi: 10.1016/j.jeurceramsoc.2005.01.030
- Waku Y, Nakagawa N, Wakamoto T, Ohtsubo H, Shimizu K, Kohtoku Y. A ductile ceramic eutectic composite with high strength at 1,873 K. Nature. 1997;389(6646):49-52. doi: 10.1038/37937
- Waku Y. A new ceramic eutectic composite with high strength at 1873 K. Adv Mater. 1998;10(8):615-617. doi: 10.1002/(SICI)1521-4095(199805)10:8<615::AID-ADMA615>3.0.CO;2-T
- Llorca J, Orera VM. Directionally solidified eutectic ceramic oxides. Prog Mater Sci. 2006;51(6):711-809. doi: 10.1016/j.pmatsci.2005.10.002
- Gu D, Shi X, Poprawe R, Bourell DL, Setchi R, Zhu J. Material-structure-performance integrated laser-metal additive manufacturing. Science. 2021;372(6545):eabg1487. doi: 10.1126/science.abg1487
- Chen Z, Li Z, Li J, et al. 3D printing of ceramics: a review. J Eur Ceram Soc. 2019;39(4):661-687. doi: 10.1016/j.jeurceramsoc.2018.11.013
- Yin H, Bai P, Liu B, Li Y. Present situation and development trend of selective laser melting technology for metal powder. Hot Work Technol. 2010;39(1):140-144. [In Chinese]. doi: 10.3969/j.issn.1001-3814.2010.01.045
- Liu WJ, Zhang K, Wang HR, Bian HY. Research status and application progress of laser directed energy deposition technology. J Shenyang Univ Technol. 2024;46(5):631-645. [In Chinese]. doi: 10.7688/j.issn.1000-1646.2024.05.12
- Pfeiffer S, Florio K, Puccio D, et al. Direct laser additive manufacturing of high performance oxide ceramics: a state-of-the-art review. J Eur Ceram Soc. 2021;41(13):6087-6114. doi: 10.1016/j.jeurceramsoc.2021.05.035
- Zhang F, Gao P, Tan H, et al. Tailoring grain morphology in Ti-6Al-3Mo through heterogeneous nucleation in directed energy deposition. J Mater Sci Technol. 2021;88:132-142. doi: 10.1016/j.jmst.2021.01.056
- Chakraborty A, Tangestani R, Batmaz R, et al. In-process failure analysis of thin-wall structures made by laser powder bed fusion additive manufacturing. J Mater Sci Technol. 2022;98:233-243. doi: 10.1016/j.jmst.2021.05.017
- Kim YK, Kim MC, Lee KA. 1.45 GPa ultrastrong cryogenic strength with superior impact toughness in the in-situ nano oxide reinforced CrMnFeCoNi high-entropy alloy matrix nanocomposite manufactured by laser powder bed fusion. J Mater Sci Technol. 2022;97:10-19. doi: 10.1016/j.jmst.2021.04.030
- Xing LL, Zhao CC, Chen H, Shen ZJ, Liu W. Microstructure of a Ti-50 wt% Ta alloy produced via laser powder bed fusion. Acta Metall Sin (Engl Lett). 2020;33(7):981-990. doi: 10.1007/s40195-020-01052-w
- Ebrahimnia M, Xie Y, Chi C. Effect of laser power and deposition environment on the microstructure and properties of direct laser metal-deposited 12CrNi2 steel. Acta Metall Sin (Engl Lett). 2020;33(4):528-538. doi: 10.1007/s40195-019-00974-4
- Yu C, Zhong Y, Zhang P, et al. Effect of build direction on fatigue performance of L-PBF 316L stainless steel. Acta Metall Sin (Engl Lett). 2020;33(4):539-550. doi: 10.1007/s40195-019-00983-3
- Wang X, Lv F, Shen LD, Liang HX, Xie DQ, Tian ZJ. Influence of island scanning strategy on microstructures and mechanical properties of direct laser-deposited Ti-6Al-4V structures. Acta Metall Sin (Engl Lett). 2019;32(9):1173-1180. doi: 10.1007/s40195-018-0858-6
- Deckers J, Meyers S, Kruth JP, Vleugels J. Direct selective laser sintering/melting of high density alumina powder layers at elevated temperatures. Phys Procedia. 2014;56:117-124. doi: 10.1016/j.phpro.2014.08.154
- Ullah A, Ur Rehman A, Salamci MU, Pıtır F, Liu T. The influence of laser power and scanning speed on the microstructure and surface morphology of Cu2O parts in SLM. Rapid Prototyp J. 2022;28(9):1796-1807. doi: 10.1108/RPJ-12-2021-0342
- Wilkes J, Hagedorn Y, Meiners W, Wissenbach K. Additive manufacturing of ZrO2-Al2O3 ceramic components by selective laser melting. Rapid Prototyp J. 2013;19(1):51-57. doi: 10.1108/13552541311292736
- Liu H, Su H, Shen Z, et al. Direct formation of Al2O3/GdAlO3/ZrO2 ternary eutectic ceramics by selective laser melting: microstructure evolutions. J Eur Ceram Soc. 2018;38(15):5144-5152. doi: 10.1016/j.jeurceramsoc.2018.07.040
- Fan Z, Lu M, Huang H. Selective laser melting of alumina: a single track study. Ceram Int. 2018;44(8):9484-9493. doi: 10.1016/j.ceramint.2018.02.166
- Niu FY, Wu DJ, Ma GY, Zhang B. Additive manufacturing of ceramic structures by laser engineered net shaping. Chin J Mech Eng. 2015;28(6):1117-1122. doi: 10.3901/CJME.2015.0608.078
- Wu D, Yu X, Zhao Z, et al. Direct additive manufacturing of TiCp reinforced Al2O3-ZrO2 eutectic functionally graded ceramics by laser directed energy deposition. J Eur Ceram Soc. 2023;43(6):2718-2723. doi: 10.1016/j.jeurceramsoc.2022.12.068
- Rao H, Oleksak RP, Favara K, Harooni A, Dutta B, Maurice D. Behavior of yttria-stabilized zirconia (YSZ) during laser direct energy deposition of an Inconel 625 YSZ cermet. Addit Manuf. 2020;31:100932. doi: 10.1016/j.addma.2019.100932
- Liu H, Su H, Shen Z, et al. One-step additive manufacturing and microstructure evolution of melt-grown Al2O3/GdAlO3/ZrO2 eutectic ceramics by laser directed energy deposition. J Eur Ceram Soc. 2021;41(6):3547-3558. doi: 10.1016/j.jeurceramsoc.2021.01.047
- Liu H, Su H, Shen Z, et al. Insights into high thermal stability of laser additively manufactured Al2O3/GdAlO3/ZrO2 eutectic ceramics under high temperatures. Addit Manuf. 2021;48:102425. doi: 10.1016/j.addma.2021.102425
- Liu H, Su H, Shen Z, et al. Preparation of large-size Al2O3/GdAlO3/ZrO2 ternary eutectic ceramic rod by laser directed energy deposition and its microstructure homogenization mechanism. J Mater Sci Technol. 2021;85:218-223. doi: 10.1016/j.jmst.2021.01.025
- Liu H, Jiang H, Shen Z, et al. Microstructure evolution and mechanical property of melt-grown Al2O3/GdAlO3/ZrO2 eutectic ceramics prepared by laser directed energy deposition. Ceram Int. 2024;50(13):22565-22573. doi: 10.1016/j.ceramint.2024.03.358
- Li F, Zhang X, Sui C, Wu J, Wei H, Zhang Y. Microstructure and mechanical properties of Al2O3-ZrO2 ceramic deposited by laser direct material deposition. Ceram Int. 2018;44(15):18960-18968. doi: 10.1016/j.ceramint.2018.07.135
- Li F, Liu Z, Li B, Wang Y, Zhang Y. Pore formation model for direct laser deposition of Al2O3-ZrO2 ceramic. J Eur Ceram Soc. 2022;42(1):207-215. doi: 10.1016/j.jeurceramsoc.2021.09.042
- Hu Y, Ning F, Cong W, Li Y, Wang X, Wang H. Ultrasonic vibration-assisted laser engineering net shaping of ZrO2-Al2O3 bulk parts: effects on crack suppression, microstructure, and mechanical properties. Ceram Int. 2018;44(3):2752-2760. doi: 10.1016/j.ceramint.2017.11.013
- Fan Z, Zhao Y, Lu M, Huang H. Yttria stabilized zirconia (YSZ) thin wall structures fabricated using laser engineered net shaping (LENS). Int J Adv Manuf Technol. 2019;105(11):4491-4498. doi: 10.1007/s00170-019-03322-z
- Niu F, Wu D, Yan S, Ma G, Zhang B. Process optimization for suppressing cracks in laser engineered net shaping of Al2O3 ceramics. JOM. 2017;69(3):557-562. doi: 10.1007/s11837-016-2191-8
- Huang Y, Wu D, Zhao D, et al. Process optimization of melt growth alumina/aluminum titanate composites directed energy deposition: effects of scanning speed. Addit Manuf. 2020;35:101210. doi: 10.1016/j.addma.2020.101210
- Mishra GK, Paul CP, Rai AK, Agrawal AK, Rai SK, Bindra KS. Experimental investigation on laser directed energy deposition based additive manufacturing of Al2O3 bulk structures. Ceram Int. 2021;47(4):5708-5720. doi: 10.1016/j.ceramint.2020.10.157
- Niu F, Wu D, Zhou S, Ma G. Power prediction for laser engineered net shaping of Al2O3 ceramic parts. J Eur Ceram Soc. 2014;34(15):3811-3817. doi: 10.1016/j.jeurceramsoc.2014.06.023
- Hu Y, Cong W. A review on laser deposition-additive manufacturing of ceramics and ceramic reinforced metal matrix composites. Ceram Int. 2018;44(17):20599-20612. doi: 10.1016/j.ceramint.2018.08.083
- Hu Y, Ning F, Wang X, et al. Laser deposition-additive manufacturing of in situ TiB reinforced titanium matrix composites: TiB growth and part performance. Int J Adv Manuf Technol. 2017;93(9-12):3409-3418. doi: 10.1007/s00170-017-0769-0
- Sing SL, Yeong WY, Wiria FE, et al. Direct selective laser sintering and melting of ceramics: a review. Rapid Prototyp J. 2017;23(3):611-623. doi: 10.1108/RPJ-11-2015-0178
- Singh N, Hameed P, Ummethala R, Manivasagam G, Prashanth KG, Eckert J. Selective laser manufacturing of Ti-based alloys and composites: impact of process parameters, application trends, and future prospects. Mater Today Adv. 2020;8:100097. doi: 10.1016/j.mtadv.2020.100097
- Huang W, Yang J, Yang H, Jing G, Wang Z, Zeng X. Heat treatment of Inconel 718 produced by selective laser melting: microstructure and mechanical properties. Mater Sci Eng A. 2019;750:98-107. doi: 10.1016/j.msea.2019.02.046
- Suryawanshi J, Prashanth KG, Ramamurty U. Mechanical behavior of selective laser melted 316L stainless steel. Mater Sci Eng A. 2017;696:113-121. doi: 10.1016/j.msea.2017.04.058
- Zheng Y, Zhang K, Liu TT, Liao WH, Zhang CD, Shao H. Cracks of alumina ceramics by selective laser melting. Ceram Int. 2019;45(1):175-184. doi: 10.1016/j.ceramint.2018.09.149
- Hagedorn YC, Wilkes J, Meiners W, Wissenbach K, Poprawe R. Net shaped high performance oxide ceramic parts by selective laser melting. Phys Procedia. 2010;5:587-594. doi: 10.1016/j.phpro.2010.08.086
- Denry I, Holloway JA. Ceramics for dental applications: a review. Materials (Basel). 2010;3(1):351-368. doi: 10.3390/ma3010351
- Bertrand P, Bayle F, Combe C, Goeuriot P, Smurov I. Ceramic components manufacturing by selective laser sintering. Appl Surf Sci. 2007;254(4):989-992. doi: 10.1016/j.apsusc.2007.08.085
- Shishkovsky I, Yadroitsev I, Bertrand P, Smurov I. Alumina-zirconium ceramics synthesis by selective laser sintering/melting. Appl Surf Sci. 2007;254(4):966-970. doi: 10.1016/j.apsusc.2007.09.001
- Khmyrov RS, Protasov CE, Grigoriev SN, Gusarov AV. Crack-free selective laser melting of silica glass: single beads and monolayers on the substrate of the same material. Int J Adv Manuf Technol. 2016;85(5-8):1461-1469. doi: 10.1007/s00170-015-8051-9
- Liu Q, Danlos Y, Song B, Zhang B, Yin S, Liao H. Effect of high-temperature preheating on the selective laser melting of yttria-stabilized zirconia ceramic. J Mater Process Technol. 2015;222:61-74. doi: 10.1016/j.jmatprotec.2015.02.036
- Liu Q, Song B, Liao H. Microstructure study on selective laser melting yttria stabilized zirconia ceramic with near IR fiber laser. Rapid Prototyp J. 2014;20(5):346-354. doi: 10.1108/RPJ-12-2012-0113
- Wu D, Shi J, Niu F, Ma G, Zhou C, Zhang B. Direct additive manufacturing of melt growth Al2O3-ZrO2 functionally graded ceramics by laser directed energy deposition. J Eur Ceram Soc. 2022;42(6):2957-2973. doi: 10.1016/j.jeurceramsoc.2022.01.034
- Li Y, Hu Y, Cong W, Zhi L, Guo Z. Additive manufacturing of alumina using laser engineered net shaping: effects of deposition variables. Ceram Int. 2017;43(10):7768-7775. doi: 10.1016/j.ceramint.2017.03.085
- Yang Y, Gong Y, Qu S, Xin B, Xu Y, Qi Y. Additive/subtractive hybrid manufacturing of 316L stainless steel powder: densification, microhardness and residual stress. J Mech Sci Technol. 2019;33(12):5797-5807. doi: 10.1007/s12206-019-1126-z
- Boisselier D, Sankaré S, Engel T. Improvement of the laser direct metal deposition process in 5-axis configuration. Phys Procedia. 2014;56:239-249. doi: 10.1016/j.phpro.2014.08.168
- Li L, Haghighi A, Yang Y. A novel 6-axis hybrid additive-subtractive manufacturing process: design and case studies. J Manuf Process. 2018;33:150-160. doi: 10.1016/j.jmapro.2018.05.008
- Balla VK, Bose S, Bandyopadhyay A. Processing of bulk alumina ceramics using laser engineered net shaping. Int J Appl Ceram Technol. 2008;5(3):234-242. doi: 10.1111/j.1744-7402.2008.02202.x
- Bernard SA, Balla VK, Bose S, Bandyopadhyay A. Direct laser processing of bulk lead zirconate titanate ceramics. Mater Sci Eng B. 2010;172(1):85-88. doi: 10.1016/j.mseb.2010.04.022
- Triantafyllidis D, Li L, Stott H. Modeling of boundary porosity formation in laser melting and re-solidification of ceramics. J Am Ceram Soc. 2006;89(4):1286-1294. doi: 10.1111/j.1551-2916.2006.00909.x
- Bianchi MVA, Viskanta R. Gas segregation during solidification processes. Int J Heat Mass Transf. 1997;40(9):2035-2043. doi: 10.1016/S0017-9310(96)00283-9
- Chang Z, Ma C, Fan X, Huang J, Liu Z, Li F. Influence of laser power on the forming quality of Al2O3 ceramic in directed energy deposition. Ceram Int. 2025;51(15):20381-20394. doi: 10.1016/j.ceramint.2025.02.204
- Niu F, Wu D, Lu F, Liu G, Ma G, Jia Z. Microstructure and macro properties of Al2O3 ceramics prepared by laser engineered net shaping. Ceram Int. 2018;44(12):14303-14310. doi: 10.1016/j.ceramint.2018.05.036
- Mostafaei A, Zhao C, He Y, et al. Defects and anomalies in powder bed fusion metal additive manufacturing. Curr Opin Solid State Mater Sci. 2022;26(2):100974. doi: 10.1016/j.cossms.2021.100974
- Jiang H, Su H, Yu M, et al. Insights into the influence of powder particle shape on forming process and mechanical properties of Al2O3 ceramic fabricated by laser directed energy deposition. Addit Manuf. 2024;81:103984. doi: 10.1016/j.addma.2024.103984
- Liu Z, Ma C, Chang Z, et al. Formation mechanism and quantitative analysis of pores in Al2O3-ZrO2 ceramic different structures by laser additive manufacturing. Ceram Int. 2023;49(10):16099-16109. doi: 10.1016/j.ceramint.2023.01.208
- Li C, Wang W. Quantitative characterization of lamellar microstructure of plasma-sprayed ceramic coatings through visualization of void distribution. Mater Sci Eng A. 2004;386(1-2):10-19. doi: 10.1016/S0921-5093(04)00900-1
- Su H, Liu H, Jiang H, et al. One-step preparation of melt-grown Al2O3/GdAlO3/ZrO2 eutectic ceramics with large size and irregular shape by directed energy deposition. Addit Manuf. 2023;70:103563. doi: 10.1016/j.addma.2023.103563
- Huang Y, Wu D, Yu X, et al. Cracking mechanism in laser directed energy deposition of melt growth alumina/aluminum titanate ceramics. J Am Ceram Soc. 2023;106(7):4358-4370. doi: 10.1111/jace.19080
- Niu FY. Cracking Mechanism and Suppressing Methods for Laser Melting Deposition of Al2O3 Ceramic [dissertation]. Dalian, China: Dalian University of Technology; 2017.
- Li JF, Li L, Stott FH. Thermal stresses and their implication on cracking during laser melting of ceramic materials. Acta Mater. 2004;52(14):4385-4398. doi: 10.1016/j.actamat.2004.06.005
- Wu D, Lu F, Zhao D, et al. Effect of doping SiC particles on cracks and pores of Al2O3-ZrO2 eutectic ceramics fabricated by directed laser deposition. J Mater Sci. 2019;54(13):9321-9330. doi: 10.1007/s10853-019-03555-z
- Pappas JM, Thakur AR, Dong X. Effects of zirconia doping on additively manufactured alumina ceramics by laser direct deposition. Mater Des. 2020;192:108711. doi: 10.1016/j.matdes.2020.108711
- Fan Z, Yin Y, Tan Q, et al. Unveiling solidification mode transition and crystallographic characteristics in laser 3D-printed Al2O3-ZrO2 eutectic ceramics. Scr Mater. 2022;210:114433. doi: 10.1016/j.scriptamat.2021.114433
- Liu H, Su H, Shen Z, et al. Effect of scanning speed on the solidification process of Al2O3/GdAlO3/ZrO2 eutectic ceramics in a single track by selective laser melting. Ceram Int. 2019;45(14):17252-17257. doi: 10.1016/j.ceramint.2019.05.281
- Zhang J, Su H, Song K, Liu L, Fu H. Microstructure, growth mechanism and mechanical property of Al2O3-based eutectic ceramic in situ composites. J Eur Ceram Soc. 2011;31(7):1191-1198. doi: 10.1016/j.jeurceramsoc.2010.11.008
- Ur Rehman A, Ullah A, Liu T, Ur Rehman R, Salamci MU. Additive manufacturing of Al2O3 ceramics with MgO/SiC contents by laser powder bed fusion process. Front Chem. 2023;11:1034473. doi: 10.3389/fchem.2023.1034473
- Pappas JM, Dong X. Porosity characterization of additively manufactured transparent MgAl2O4 spinel by laser direct deposition. Ceram Int. 2020;46(5):6745-6755. doi: 10.1016/j.ceramint.2019.11.164
- Juste E, Petit F, Lardot V, Cambier F. Shaping of ceramic parts by selective laser melting of powder bed. J Mater Res. 2014;29(17):2086-2094. doi: 10.1557/jmr.2014.127
- Wu DJ, Huang YF, Zhao DK, Niu FY, Ma GY. Microstructure and mechanical properties of melt growth alumina/aluminum titanate composite ceramics prepared by directed laser deposition. J Mech Eng. 2022;58(14):212-222. [In Chinese]. doi: 10.3901/JME.2022.14.212
- Liu Z, Song K, Gao B, et al. Microstructure and mechanical properties of Al2O3/ZrO2 directionally solidified eutectic ceramic prepared by laser 3D printing. J Mater Sci Technol. 2016;32(4):320-325. doi: 10.1016/j.jmst.2015.11.017
- Savalani MM, Pizarro JM. Effect of preheat and layer thickness on selective laser melting (SLM) of magnesium. Rapid Prototyp J. 2016;22(1):115-122. doi: 10.1108/RPJ-07-2013-0076
- Yan S, Huang Y, Zhao D, Niu F, Ma G, Wu D. 3D printing of nano-scale Al2O3-ZrO2 eutectic ceramic: principle analysis and process optimization of pores. Addit Manuf. 2019;28:120-126. doi: 10.1016/j.addma.2019.04.024
- Yan S, Wu D, Niu F, Huang Y, Liu N, Ma G. Effect of ultrasonic power on forming quality of nano-sized Al2O3-ZrO2 eutectic ceramic via laser engineered net shaping (LENS). Ceram Int. 2018;44(1):1120-1126. doi: 10.1016/j.ceramint.2017.10.067
- Yu W, Liu Y, Wang F, Jiang F, Zarinejad M, Tong Y. Effect of synchronous ultrasonic assistance on defects of Ti6Al4V alloy fabricated by laser directed energy deposition. Mater Today Commun. 2025;42:111527. doi: 10.1016/j.mtcomm.2025.111527
- Florio K, Pfeiffer S, Makowska M, et al. An innovative selective laser melting process for hematite-doped aluminum oxide. Adv Eng Mater. 2019;21(6):1801352. doi: 10.1002/adem.201801352
- Wu D, Yu X, Zhao Z, et al. One-step additive manufacturing of TiCp reinforced Al2O3-ZrO2 eutectic ceramics composites by laser directed energy deposition. Ceram Int. 2023;49(8):12758-12771. doi: 10.1016/j.ceramint.2022.12.141
- Fan Z, Zhao Y, Tan Q, et al. Nanostructured Al2O3-YAG-ZrO2 ternary eutectic components prepared by laser engineered net shaping. Acta Mater. 2019;170:24-37. doi: 10.1016/j.actamat.2019.03.020
- Yan S, Wu D, Niu F, Ma G, Kang R. Al2O3-ZrO2 eutectic ceramic via ultrasonic-assisted laser engineered net shaping. Ceram Int. 2017;43(17):15905-15910. doi: 10.1016/j.ceramint.2017.08.165
- Fan Z, Tan Q, Yuan L, et al. Solute-induced grain refinement for crack suppression in laser additive manufactured ceramics. Acta Mater. 2025;292:121069. doi: 10.1016/j.actamat.2025.121069
- Pfeiffer S, Florio K, Makowska M, et al. Crack-reduced alumina/aluminum titanate composites additive manufactured by laser powder bed fusion of black TiO2-x doped alumina granules. J Eur Ceram Soc. 2022;42(8):3515-3529. doi: 10.1016/j.jeurceramsoc.2022.02.046
- Niu F, Wu D, Huang Y, et al. Direct additive manufacturing of large-sized crack-free alumina/aluminum titanate composite ceramics by directed laser deposition. Rapid Prototyp J. 2019;25(8):1370-1378. doi: 10.1108/RPJ-08-2018-0215
